Raspberry Pi Rackmount Kit | 4x Slot – 58x20mm | 4x Connector | 19 inch | 1.00U | Rail System 200mm

>> Suitable for all Single Board Computers (SBC) with Raspberry Pi form factor

19" Raspberry Pi rack
19" Raspberry Pi rackmount
19" Raspberry Pi rack mount
19" Raspberry Pi
Raspberry Pi rack
Raspberry Pi rack mount
Raspberry Pi rackmount
19" Raspberry Pi rack - UM-SBC-209
19" Raspberry Pi rackmount - UM-SBC-209
19" Raspberry Pi rack mount - UM-SBC-209
19" Raspberry Pi - UM-SBC-209
Raspberry Pi rack - UM-SBC-209
Raspberry Pi rack mount - UM-SBC-209
Raspberry Pi rackmount - UM-SBC-209
previous arrow
next arrow
19" Raspberry Pi rack - UM-SBC-209
19" Raspberry Pi rackmount - UM-SBC-209
19" Raspberry Pi rack mount - UM-SBC-209
19" Raspberry Pi - UM-SBC-209
Raspberry Pi rack - UM-SBC-209
Raspberry Pi rack mount - UM-SBC-209
Raspberry Pi rackmount - UM-SBC-209
previous arrow
next arrow

The illustrations shown, partly with cables shown schematically, are symbolic representations. They can contain extras that are subject to a surcharge (see configurator).

The illustrations shown, partly with cables shown schematically, are symbolic representations. They can contain extras that are subject to a surcharge (see configurator).

4x Pi on 1.00U in the 19 inch server cabinet

With the “UM-SBC-209” you can neatly accommodate up to four Raspberry Pi´s or similar SBCs on 1.00U in the 19″ Rack. Each Pi is screwed to the Rackmount Kit four times with M2.5 screws (included in the scope of supply). After mounting the Pi´s on the rack, you have 34 mm from the bottom of the circuit board to top of the Raspberry Pi Rack for possible structures (PoE-HAT, USV). Single board computers are not included.

Details

Configuration options of the “UM-SBC-209”

Like every Raspberry Pi Rackmount Kit from us, you can configure the “UM-SBC-209” according to your specific needs.

Rail System

This allows your devices to be conveniently operated by pulling out the rackmount kit. A telescopic rail on each side of the Raspberry Rack allows for easy access. The rail extension is 200 mm. We recommend it if you want to always have access to your memory card without dismantling the rackmount kit.

Keystone Inline Coupler

For each Pi a keystone connector slot is avaliable. Choose the keystone inline coupler type you need. Note that the “Push Button Connector” needs to be soldered.

LEDs

To display the status LEDs of your Pi on the front. Must be glued and soldered when assembling.

Fan 40×40

The “UM-SBC-209” offers a mounting option for up to 4 fans (40 x 40 mm with a hole spacing of 32 x 32 mm). This allows the devices to be additionally ventilated. Each fan attaches to the rackmount kit with two screws directly behind the Pi.

Slot Display

The slot display is a bracket that allows a display to be installed in the rack kit. It occupies one Pi slot and mounts in the same rackmount kit holes as the Pi. Can be used to display important information about your running system. Note that the display is not included.

Slot Cover

This allows free slots in the rackmount kit to be covered. It mounts to the same rackmount kit holes as the Pi. Perfect if you want to temporarily cover one or more slots and upgrade your system at a later date.

Rack Panel 1.00U

This allows the free space of the rack mount kit to be closed up to the next full rack unit. You can choose between an air or blank version.

UM-SBC-209

5.00 out of 5
(1 costumer reviews)

Delivery time: 4-5 days In Stock

Supported Models:
Raspberry Pi 2B
Raspberry Pi 3B
Raspberry Pi 3B+
Raspberry Pi 4B
Raspberry Pi 5
SBC with Raspberry Pi form factor | Details

Rack: 19 inch
Rack Unit: 1.00U
Material: Steel
Color: Black RAL 9005
Dimensions*: 482.6 x 43.4 x 210 mm

*) Dimensions = width/height/depth

Price starting from:

159,00 

4x Pi on 1.00U in the 19 inch server cabinet

With the “UM-SBC-209” you can neatly accommodate up to four Raspberry Pi´s or similar SBCs on 1.00U in the 19″ Rack. Each Pi is screwed to the Rackmount Kit four times with M2.5 screws (included in the scope of supply). After mounting the Pi´s on the rack, you have 34 mm from the bottom of the circuit board to top of the Raspberry Pi Rack for possible structures (PoE-HAT, USV). Single board computers are not included.

Details

Configuration options of the “UM-SBC-209”

Like every Raspberry Pi Rackmount Kit from us, you can configure the “UM-SBC-209” according to your specific needs.

Rail System

This allows your devices to be conveniently operated by pulling out the rackmount kit. A telescopic rail on each side of the Raspberry Rack allows for easy access. The rail extension is 200 mm. We recommend it if you want to always have access to your memory card without dismantling the rackmount kit.

Keystone Inline Coupler

For each Pi a keystone connector slot is avaliable. Choose the keystone inline coupler type you need. Note that the “Push Button Connector” needs to be soldered.

LEDs

To display the status LEDs of your Pi on the front. Must be glued and soldered when assembling.

Fan 40×40

The “UM-SBC-209” offers a mounting option for up to 4 fans (40 x 40 mm with a hole spacing of 32 x 32 mm). This allows the devices to be additionally ventilated. Each fan attaches to the rackmount kit with two screws directly behind the Pi.

Slot Display

The slot display is a bracket that allows a display to be installed in the rack kit. It occupies one Pi slot and mounts in the same rackmount kit holes as the Pi. Can be used to display important information about your running system. Note that the display is not included.

Slot Cover

This allows free slots in the rackmount kit to be covered. It mounts to the same rackmount kit holes as the Pi. Perfect if you want to temporarily cover one or more slots and upgrade your system at a later date.

Rack Panel 1.00U

This allows the free space of the rack mount kit to be closed up to the next full rack unit. You can choose between an air or blank version.

Configurator

Configure the Rack Mount Kit according to your requirements here.

159,00 

Delivery time: 4-5 days In Stock

In stock

  • This allows your devices to be conveniently operated by pulling out the rack mount kit.

  • This allows the rear connections of your device to be operated on the front of the rack mount kit.

    *Connector 1
    *Connector 2
    *Connector 3
    *Connector 4
  • This allows the devices to be additionally ventilated.

  • This allows the status of your device to be displayed on the front of the rackmount kit.
    *LED green
    *LED red
    *LED yellow
  • The Slot Display is a bracket that allows your display to be installed in the rack mount kit.

    Note:

    Not compatible in combination with LEDs.

    Not suitable with Fan 40.

    More Information

    Note:

    Not compatible in combination with LEDs.

    Not suitable with Fan 40.

    More Information

    Note:

    Not suitable with Fan 40.

    More Information

    Note:

    Not suitable with Fan 40.

    More Information

  • This allows unused slots to be covered temporarily or permanently.

  • This allows the free space of the rack mount kit to be closed up to the next full rack unit.

Available build space for Raspberry Pi add-on boards

If you are toying with the idea of accommodating additional boards such as PoE-HAT or UPS in the rack, you will find the available scope below.

For 1.00U Raspberry Pi Rack Mount Kits

From the lower edge of the circuit board to the lower edge of the slot, you have 35.4mm available.

raspberry-pi-rack-mount-kits-1u-space

For 1.33U Raspberry Pi Rack Mount Kits

From the lower edge of the circuit board to the lower edge of the slot, you have 50.2mm available.

raspberry-pi-rack-mount-kits-1-33u-space

For 2.00U Raspberry Pi Rack Mount Kits

From the lower edge of the circuit board to the lower edge of the slot, you have 87.8mm available.

raspberry-pi-rack-mount-kits-2u-space

Single Board Computer with identical form factor for Raspberry Pi

As mentioned above, you can mount single board computers with the same form factor as the Pi 5 in the Raspberry Pi Rackmount Kit. Pay attention to the basic dimensions of the Pi and the drilling pattern/diameter.

If they match, your single-board computers are compatible with our rack and can therefore be used without any problems. Single board computers tested by us for compatibility are: ASUS Tinker Board | ODROID-C1+

single-board-computer-with-identical-form-factor-for-raspberry-pi

1 review for UM-SBC-209

  1. Henning Halfpap

    A nice way to get up to 4 Pis in therack – but do plan thoroughly!

    Pros:
    – very tidy solution to mount up to 4 Raspberry Pis
    – Low rackspace usage due to only 1U used
    – very stable
    – a total of 4 keystone slots to pass through connectors to the front
    – lots of customisation options
    – very high build quality

    Cons:
    – Tight space due to the compact format (e.g. putting a raspberry Pi in the left slot and routing an HDMI cable from there is almost impossible)
    – Hats on the Top of the Pi (e.g. a PoE hat) will fit nicely, but bottom placed hats (like M.2 SSD USB devices) might be difficult unless the connectors face backwards, which in turn might lead to conlicts with possible fans mounted in that location
    – Use of LEDs is difficult as the space between the slot and the keystone slot, where the LED holes are located, is extremely tight
    – No LED-PCB and matching mounting screw sockets are available – currently the only option is to glue the LEDs into their sockets
    – with the 16×2 LCD panel mounted, using LEDs in the same slot becomes very difficult, if not impossible, as the LCD’s PCB overlaps the LED holes

    Although I had one or two issues while building my Setup – which occured mostly due to my lack of planning / experience – I am very happy about how my build turned out. Note that, although there’s rack rails available, this is not so much a solution for tinkering, but rather a permanent build. Although you can access everything in the mount quite easily if you pull it out, it will most probably be screwed on to the mount. For a more tinker-friendly solution I’d probably search for one that allows to remove the Pi as a module individually. But apart from that, for my purpose, it is just the perfect solution!

    Verified Purchase

Only logged in customers who have purchased this product may leave a review.